Kit Review: Atlantis Models 1/92 B-24J (2024)

SUMMARY: Ancient kit, but better than you'd expect. The low price seals the deal.

As an acknowledgment that this is not a state-of-the-art kit, Atlantis set the retail price at only $21.99. Other manufacturers circa 2019 would probably charge $30 or more to re-release this kit, but to debut an item at this low price is impressive. With this in mind, it is a perfect kit for a newer modeler who wishes to build their skills on an inexpensive subject. Atlantis has an agreement to retail some of their kits at Hobby Lobby, a nationwide craft store chain in the USA, and this is where I picked up H218, “B24J Liberator Bomber.” Using a discount coupon put the cost comparable, adjusting for inflation, to a price range that would have been easily affordable using a little paper route money or weekly allowance back in the day.

If you’d prefer, you can check out the Wikipedia article on the B-24 here first. It’s much better than what I could write anyway. We focus a bit more on the history of the kit itself.Atlantis’ B-24J is basically a re-issue of Revell’s classic Buffalo Bill version of the kit that first appeared in 1954. Revell’s early aircraft kits were all “box scale,” meaning that they fit a standard box, which by the way, was a fair bit smaller than the box that Atlantis is using. A later issue of the kit by Revell has also been released by Atlantis; B-24J Liberator Pacific Raider, features different box art and decals.

Revell came out with a completely new 1/72 B-24D kit in about 1964. Detailing for that kit was a bit more refined, as Revell’s tooling staff had taken full advantage of their experience releasing many kits in the late 1950’s during which they perfected their craft. Models of that era are iconic today for their intricate detail. This earlier B-24J kit is a little less advanced than that standard. But that’s not to say it can’t be built into a nice model, and it’s important that the buyer understand that they are not getting the later B-24 kit, which is the earlier “D” variant of the B-24. Just remember that the older kit is actually the later B-24 "J" variant.

The Atlantis kit, all made in the USA, had less flash and sinkholes than I expected to find. Either they’ve cleaned up the mold, or it has aged better than average. The most apparent issue the modeler will notice upon opening the kit is a molding defect that makes the right-side vertical stabilizer appear to have a scalloped trailing edge. This is very easy to fix and I hope that no potential builder passes on the kit because of this minor defect, which may be related to a slightly warped or damaged mold. Perhaps this is the reason that the original Revell declined to reissue the kit in a number of decades.

To fix the scalloped tailpiece, I stretched some kit sprue, and glued a piece to the one end of the scalloped trailing edge. After letting that dry, I carefully curved the stretched sprue over the scallops, carefully gluing it to the tall points of the scallops until they were all covered. I used small strips of masking tape to hold the thin sprue piece in place, being careful not to get liquid cement near the tape.

Once this has set and the tape is removed, the modeler can use their favorite medium to fill the small openings remaining; some kind of putty, epoxy, or CYA (“super glue”) will generally be used. I decided to shave a small pile of sprue onto a piece of cardboard, and mixed it up with Testor’s liquid cement to make a slurry of melted plastic. This was spread into the openings with a toothpick. This method must allow some extra time or elevated temperature to bake out the glue solvent; simply putting the treated kit piece in my hot garage for a day or two (it’s late summer as I begin this kit) did the trick. Other than the prep time and dry-time, this fix took just a few minutes! Much of the satisfaction we get from scale model building is improving what comes out of the box. Again, I must reiterate that the issue with this piece does not need to dissuade anybody from purchasing the kit since it is so easy to fix.

Like most model airplane kits of the era, this one has its share of rivets. One unique quirk of these rivets is that they sit tall! I’d recommend sanding them down just a tad to make them less prominent. They’d have to be a couple inches tall in-scale. There’s no ignoring that this is a vintage kit, which is why I plan to leave them there, although toned down just a bit. 320 or 400 grit wet-sandpaper worked great.

There are a few minor items to consider to help parts fit. On wings and fuselage joining surfaces, there are some round pin ejector marks that should be scraped or sanded off. Like most models, and especially vintage kits like this, parts should be test-fitted carefully before gluing.

I sanded the wings down just a little at the gluing surfaces. Thinning them more would have improved the trailing edge appearance, but a thinner wing might have created more of a gap where the wings join the fuselage. Fit there, by the way, was pretty good; it looks like only a small amount of putty might be needed at the wing joint to produce a contest-quality model. For a fun-build, the minor gap might not even matter.

Overall, I’m pretty impressed with general fit of all parts considering the age of the kit—it’s actually about old enough to begin claiming Social Security retirement benefits (that happens at age 65 nowadays in the USA). How many products can you name that are that old that are still relevant in their unmodified form in our fast-evolving world.

​Engine faces are an admittedly weak point of the kit, with a simple depression instead of an open cowling with an engine piece or two as you'd see in later kits. The 1/72 B-24D kit at least had engine faces molded into the cowlings. With the four-blade props throwing shade on the opening anyway, it’s not glaringly noticeable.

Update: The model has been painted and weathered using the "salt chip" method. Paint is glossy, so it will accept the decals without unsightly silvering, or trapped air under the decal.

Decals are crisp and in-register. The artwork appears to be the same as the original release; that is to say simplified with no detail markings, but quality-wise, they look to be high-end grade. Considering its already low MSRP, this asset solidifies the kit as a how-do-they-do-it bargain.

I’d recommend this kit to all modelers. Beginners ought to have a little experience, perhaps with a newer glue-kit or two. Correcting the scalloped stabilizer will help the beginner advance to intermediate-level modeling. The target audience here is probably the nostalgic modeler, but the low price ought to provide an enticement to a youngster who wants to take a break from video games by engaging in a creative exercise. For the modeler trying to complete a collection of Revell’s early aircraft models, this kit is essential!

BONUS MATERIAL: MORE ABOUT THE B-24 LIBERATOR

We had a beloved uncle, Al Summerhays, who flew B-24’s over Third Reich Germany during World War II. For his service, he was awarded the Distinguished Flying Cross. At his funeral in 1992, his family related a story that we’d like to share with you. Uncle Al, who married our father’s sister, was five years older than our father, and entered the war earlier than our father did. At age 23 when the war began, Uncle Al eventually achieved the rank of Captain in the USAAF.

As you might well imagine, dropping bombs from a B-24 over Germany in WWII was extremely hazardous. A religious man, Uncle Al was known for gathering his crew together for a prayer prior to departure. During one mission, a superior officer, not part of the regular crew, came along on the bomb run as an observer. Prior to the flight, he ridiculed Al for praying with his crew. The mission was harrowing, with the plane being shot up badly, and it barely made it back to the base. Upon departing the plane, the officer again berated Al for the prayer, which he deemed to be a futile effort, considering events of the flight. Uncle Al, who was well known for speaking his mind, retorted, “Well, you made it back here, didn’t you.”

Regarding additional history of the B-24, we have posted a feature article on Yo Yo, an ETO B-24J. Brudder Dick redecorated a 1/24 diecast B-24J for an acquaintance, whose father served on the aircraft, along with Senator George McGovern during WWII. The story includes some never-before-published personal accounts about the B-24 and details about a most unique modeling project.

LEARN MORE ABOUT THE ATLANTIS B-24J

SCROLL DOWN JUST A BIT TO SEE WHAT ELSE IS GOING ON AT DEMBRUDDERS.COM--WE HAVE ALL SORTS OF CRAZY STUFF HERE!